Study the Effect of Extrusion Speed and Die Angle on Relative Extrusion Pressure of Aluminum Alloy AA6061
محتوى المقالة الرئيسي
الملخص
Theoretical and experimental study of die angle, and extrusion speed effect on relative extrusion pressure of annealed AA6061 aluminum alloy have been carried out in this research. Two theoretical fields have been employed, rigid-plastic field and mixed field, to predict the relative extrusion pressure. A FORTRAN program has been developed to calculate the relative extrusion pressure and its compounds. The tests have been conducted with various, die angle (30°,60°,90°,120°,150°) and various extrusion speed (10,7,3) mm/min.
The results showed an increase in shear power and friction power with increasing die angle, while no effect was observed on the internal power of deformation. It was also found that the relative extrusion pressure, the inhomogeneous strain, and the shear strain across the section increase as the die angle and extrusion speed increase. Experimental tests showed that the optimum die angle was 60° while the optimum die angle was between 35°-90° and 46° according to the mixed field and the rigid- plastic field respectively.
المقاييس
تفاصيل المقالة
هذا العمل مرخص بموجب Creative Commons Attribution 4.0 International License.
THIS IS AN OPEN ACCESS ARTICLE UNDER THE CC BY LICENSE http://creativecommons.org/licenses/by/4.0/
##plugins.generic.plaudit.displayName##
المراجع
- George E. Diter,”Mechanical Metall-urgy”, McGraw-Hill, 1976.
- K.Laue, H. Stenger, “Extrusion”, American Society for Metals, 1981.
- F. J. Gurney, V. Depierre, " The Influence of the Interface Condition on the Plastic Deformation Zone and the Resultant Product Integrity in Extrusion", Journal of Engineering for Industry, August 194,912-916, 1974. DOI: https://doi.org/10.1115/1.3438460
- C.C.Chen, S.I.Oh, S.Kobayashi,“Ductile Fracture in Axisymmetric Extrusion and Drawing Part1: Deformation Mechanics of Extru-sion and Drawing', Journal of Engineering for Industry ,Vol.101, 23-43, 1979. DOI: https://doi.org/10.1115/1.3439470
- Young Su Oh, "Extrusion of Axisym-metric Sections through Stream-lined and Conical Dies", A Master Thesis, Ohio University, 1987.
- Al Salmani, Farouk Mansour, “Effect of Die Geometry on the Mechanism of Direct Extrusion and Properties of 1060 Al-Alloy” Ph. D. Dissertation UOT, Baghdad, 1999.
- M. H. Skillingberg, R .F. Ashton, "Process-ing and Perfomance of Al-Li-Cu-x Extrusions", Journal De Physique, Colloque C3 ,Supplement au n 9,Tome 48, 179-186, 1987. DOI: https://doi.org/10.1051/jphyscol:1987321
- S. O. Onuh, M. Ekoja, M. B. Adeyemi, "Effects of Die Geometry and Extrusion Speed on The Cold Extrusion of Aluminum and Lead Alloys", Journal of Material Processing Technology ", Vol.132,274-285,2003. DOI: https://doi.org/10.1016/S0924-0136(02)00941-X
- Liu Gang, Zhou Jie, J. Duszczyk, "Process Optimization Diagram Based on FEM Simulation for Extrusion of AZ31 Profile", Trans. Nonferrous Met. Soc. China, Vol.18, 247-251, 2008. DOI: https://doi.org/10.1016/S1003-6326(10)60211-7
- P. Tiernan, M. T. Hillery, B. Draganescu, M. Gheorghe, "Modeling of Cold Extrusion With Experimental Verification", Journal of Materials Processing Technology ", Vol.168, 360-366, 2005. DOI: https://doi.org/10.1016/j.jmatprotec.2005.02.249
- Mahesh Prakash , Pual W.Cleary ,"Modeling of Cold Metal Extrusion Using SPH", Fifth International Conference on CDF in the Process Industries CSIRO Australia ,2006.
- Betzalal Avitzur, ”Metal Forming: Process and Analysis", McGraw, New York,1986.
- Hung-kuk Oh, Byung–Woo Ryu,"Effects of Process Variables on the Deform-ation Filed in Extrusion Through Conical Dies", Journal of Mechanical Working Technology, Vol. 11, 71-86, 1985. DOI: https://doi.org/10.1016/0378-3804(85)90113-5
- Chen, P. C. T., Ling, F. F., ”Upper bound solutions to axisymmetric extrusion problems”, Int. J. Mech. Sci., vol.10, 863–879. 1968. DOI: https://doi.org/10.1016/0020-7403(68)90090-8
- Zimerman, Z., Avitzur, B.,”Metal flow through conical die” Trans. ASME, J. Eng.Ind..vol 92, 119–129, 1970. DOI: https://doi.org/10.1115/1.3427695
- Nagpal, V., “General kinematically admissible velocity fields for some axisymmetric metal forming problem”, J. Eng. Ind, vol. 96, 1197–1201, 1974. DOI: https://doi.org/10.1115/1.3438495
- D. Y. Yang, C. H. Han and B. C. Lee, "The Use of Generalized Deformation Boundaries for the Analysis of Axisymmetric Extrusion through Curved Dies", Int. J. Mech. Sci, Vol.27, 653-663,1985. DOI: https://doi.org/10.1016/0020-7403(85)90047-5
- Wang, J. P., Kaoa, W. E., Lee, H. D., Wang, J., “Analysis of 3D rolling forming with generalized rigid-plastic boundaries approach”, J.Mater. Process. Technol. Vol. 204, 425–433, 2008. DOI: https://doi.org/10.1016/j.jmatprotec.2007.11.102
- Guo-Ming Huang, Jang-ping Wang, Hsien –Der Lee, Cheng-Sung Chang, "Rigid-Plastic Boundaries Approach to the Analysis of Arbitrary Profile Dies in Axi symmetric Extrusion', J. Materials Processing Technology, Vol.209, 4351-4359, 2009. DOI: https://doi.org/10.1016/j.jmatprotec.2008.10.037
- N. R. Chitkara, A. aleem, "Axi-symmetric Tube Extrusion –Piercing Using Die-Mandrel Combinations: Some Experiments and A Generalized Upper Bound Analysis" International Journal ofMechanical Sciences, Vol. 43, 1685 -1709, 2001. DOI: https://doi.org/10.1016/S0020-7403(00)00088-6
- George E. Totten, D. Scott Mackenzie,” Handbook of Aluminum”, Volume 1, Physical Metallugry and Processes, Marcel Dekker, Inc, New York, 2003.
- Hasan Sofuoglu, Hasan Gedikili, Jahan Rasty ,” Determination of friction Coefficient by Employing the Ring Compression Test”, Journal of Engineering Materials and Technology, Vol.12, 338-348, 2002. DOI: https://doi.org/10.1115/1.1369601
- Ozgur Kocak, "Analysis of the Formability of Metals", Master Thesis, Middle East Technical University, July 2003.
- F. Ozturk, A. Sisman, S. Toros, S. Kilic, R. C. Picu, "Influence of Aging Treatment on Mechanical Properties of 6061 Aluminum Alloy", Materials and Design, vol. 31, 972-975, 2010. DOI: https://doi.org/10.1016/j.matdes.2009.08.017
- S. K. Sahoo, "An Analysis of Plastic Flow through Polygonal Linearly Converging Dies: As Applied to Forward Metal Extrusion", Journal of Material Processing Technology, Vol.132, 286-292, 2003. DOI: https://doi.org/10.1016/S0924-0136(02)00942-1
- S. Alexandrov, G. Mishuris, W. Miszuris, R. E.Sliwa ,"On the Dead-
Zone Formation and Limit Analysis in Axially Symmetric Extrusion", International Journal of Mechanical Sciences,Vol.43, 367-379, 2001. DOI: https://doi.org/10.1016/S0020-7403(00)00016-3
- A. F. Castle and T. Sheppard, "Pressure Required to Initiate Extrusion in Some Aluminum Alloys", Met. Tec., 465-475, 1976. DOI: https://doi.org/10.1179/030716976803392123
- T. Shepprad, P. J. Tunnicliffe, S. J. Patterson, "Direct and Indirect Extrusion of High Strength Aerospace Alloy (AA 7075)", Journal of Mechanical Working Technology, Vol.6, 313-331, 1982. DOI: https://doi.org/10.1016/0378-3804(82)90031-6
- M. J. Tan, T. Sheppard ,"Extrusion processing of an Al-Li-Cu-Mg-Zr Alloy AA2091", 4thInt. Aluminum Lithium Conference, Paris (France), C33, 209-218, 10 – 12 June 1987.
- R. K. Chin, P. S. Steif, "A Computatio-nal Study of Strain Inhomogenetiy in Wire Drawing ",Int.j. Mech. Tools Manufact., Vol.35,1087-1098, 1995. DOI: https://doi.org/10.1016/0890-6955(95)90403-9
- A. Farzad, T. Z. Plazynski, "Geometry Factor and Redundancy Effects in Extrusion of Rod", Journal of Mechanical Working Technology, Vol.19, 357-372, 1989. DOI: https://doi.org/10.1016/0378-3804(89)90082-X