Experimental and Numerical Study of Heat Transfer Enhancement in a Shell and Tube Heat Exchanger using Helical Coiled Wire Inserts

Main Article Content

Ehsan Fadhil Abbas
Musa Mustafa Weis
Ahmed Sami Ridha

Abstract

An experimental work on heat transfer enhancement in a shell and tube heat exchanger by insertion of helical coiled wires into the tube bundle was conducted. Four different pitch sizes were used (4.8, 6.4, 8.0, 9.6) mm. The working fluid for both shell and tube sides of the exchanger was water. Flow arrangement used was parallel and laminar for both sides with a Reynolds number for the tube inside ranging (100-920). Variables were taken into account, including; convection heat transfer coefficient, number of heat transfer units, thermal effectiveness, and pressure drop. CFD analysis was done in order to validate the experimental results. The study results showed an increase in heat transfer coefficient on the tube side by 54% due to the use of 9.6 mm pitched inserts. Highest thermal effectiveness obtained was in the case of 9.6 mm pitch inserts. Pressure drop rose up to 260% due to inserts.

Metrics

Metrics Loading ...

Article Details

Section
Articles

Plaudit

References

Kreith F, Manglik RM, Bohn MS. Principles of heat transfer. Cengage learning; 2012.

Al-Abidi AA, Mat S, Sopian K, Sulaiman M-Y, Mohammad A-T. Internal and external fin heat transfer enhancement technique for latent heat thermal energy storage in triplex tube heat exchangers. Applied Thermal Engineering 2013; 53: 147-156. DOI: https://doi.org/10.1016/j.applthermaleng.2013.01.011

Kumar S, Karanth K, Murthy K. Numerical study of heat transfer in a finned double pipe heat exchanger. World Journal of Modelling and Simulation 2015; 11: 43-54.

Indhe MJ, Bhatkar VW. Optimization of longitudinal fin profile for double pipe heat exchanger. International Research Journal of Engineering and Technology 2015; 2 (4): 517-529

Rozzi S, Massini R, Paciello G, Pagliarini G, Rainieri S, Trifiro A. Heat treatment of fluid foods in a shell and tube heat exchanger: Comparison between smooth and helically corrugated wall tubes. Journal of Food Engineering 2007; 79: 249-254. DOI: https://doi.org/10.1016/j.jfoodeng.2006.01.050

Lin ZM, Sun DL, Wang LB. The relationship between absolute vorticity flux along the main flow and convection heat transfer in a tube inserting a twisted tape. Heat and Mass Transfer 2009; 45: 1351-1363. DOI: https://doi.org/10.1007/s00231-009-0511-z

Urkude SS, Farkade HS. Experimental investigation on heat transfer characteristics in a circular tube fitted with perforated helical screw-tape inserts. International Journal of Innovative Research in Science, Engineering and Technology 2017; 6 (5): 8713-8723.

Salman SD, Kadhum AH, Takriff MS, Mohamad AB. Heat transfer enhancement of laminar nanofluids flow in a circular tube fitted with parabolic-cut twisted tape inserts. The Scientific World Journal 2014; article ID 543231: 7 pages. DOI: https://doi.org/10.1155/2014/543231

Eiamsa-ard S, Kiatkittipong K, Jedsadaratanachai W. Heat transfer enhancement of TiO2/water nanofluid in a heat exchanger tube equipped with overlapped dual twisted-tapes. Engineering Science and Technology, an International Journal 2015; 18: 336-350. DOI: https://doi.org/10.1016/j.jestch.2015.01.008

Shewale OM, Pravin MA, Gazge SAH, Pasanna PA. Experimental investigation of double-pipe heat exchanger with helical fins on the inner rotating tube. International Journal of Research in Engineering and Technology 2014; 3 (7): 98-102. DOI: https://doi.org/10.15623/ijret.2014.0307016

Shah R-K, Sekulic D-P. Fundamentals of heat exchanger design. Hohn Wiley & Sons; 2003. DOI: https://doi.org/10.1002/9780470172605

Similar Articles

You may also start an advanced similarity search for this article.